TCCX050-G – Opto Engineering Koaksiyel Telecentric Lens
Fiyat için teklif alın
B2B ürünlerimizde güncel fiyat ve stok bilgisi için teklif talep edin — aynı gün dönüş yapıyoruz.
Coaxial telecentric lens for 2/3″ sensors, WD 132.3 mm, magnification 0.500x, green, 525 nm
Detaylar
Teknik Özellikler
| Main optical specifications | ||
| Magnification | (x) | 0.500 |
| Image circle diameter | (mm) | 11.0 |
| Max sensor size | 2/3″ | |
| Object field of view | ||
| 1/3” | (mm × mm) | 9.60 x 7.20 |
| 1/2.5” | (mm × mm) | 11.40 x 8.56 |
| 1/2” | (mm × mm) | 12.80 x 9.60 |
| 1/1.8” | (mm × mm) | 14.26 x 10.66 |
| 2/3” | (mm × mm) | 17.00 x 14.18 |
| Advanced optical specifications | ||
| Working distance (1) | (mm) | 132.3 |
| Working ƒ/N (2) | 12 | |
| Telecentricity typical (max) (3) | (deg) | < 0.04 (0.06) |
| Distortion typical (max) (4) | (%) | < 0.1 (0.2) |
| Depth of field (5) | (mm) | 2.50 |
| Resolution (6) | (μm) | 15 |
| Lighting specifications | ||
| Light color, peak wavelength | green, 525 nm | |
| Spectral FWHM | (nm) | 40 |
| Electrical specifications | ||
| Supply voltage | (V) | 12-24 |
| Max power consumption | (W) | 2.5 |
| LED voltage (7) | (V) | 3.3 (4.0) |
| LED current (8) | (mA) | 350 |
| Max pulse current (9) | (mA) | 2000 |
| Connector | M8 | |
| Cables | CB244P1500 included | |
| Mechanical specifications | ||
| Mount | C | |
| Phase adjustment | Yes | |
| Length (10) | (mm) | 131.2 |
| Front diameter | (mm) | 37.7 |
| Mass | (g) | 450 |
| Environmental specifications | ||
| Operating temperature | (°C) | 0-40 |
| Storage temperature | (°C) | 0-50 |
| Operating relative humidity | (%) | 20-85, non condensing |
| Installation | Indoor use only | |
| Eye safety | ||
| Risk group according to CEI EN 62471:2010 | Exempt | |
Last update 05 Sep 2023
- Working distance: distance between the front end of the mechanics and the object. Set this distance within ± 3% of the nominal value for maximum resolution and minimum distortion.
- Working f-number (wf/N): the real f-number of a lens in operating conditions.
- Maximum angle between chief rays and optical axis on the object side. Typical (average production) values and maximum (guaranteed) values are listed.
- Percent deviation of the real image compared to an ideal, undistorted image. Typical (average production) values and maximum (guaranteed) values are listed.
- At the borders of the field depth the image can be still used for measurement but, to get a very sharp image, only half of the nominal field depth should be considered. Pixel size used for calculation is 3.45 μm.
- Object side, calculated with the Rayleigh criterion with λ= 520 nm
- At max forward current. Tolerance is ± 0.06V on forward voltage measurements.
- Used in continuous (not pulsed) mode.
- At pulse width <= 10 ms, duty cycle <= 10% condition. Built-in electronics board must be bypassed (see tech info).
- Measured from the front end of the mechanics to the camera flange.
It’s easy to select the right lens for your application: our part numbers are coded as TCCXxxx-y, where xxx defines the magnification (050 = 0.50, 066 = 0.66, 075 = 0.75, … ) and y defines the source color (“-G” stands for “green light”, “W” stands for “white light”). For instance, a TCCX050-G features a 0.50 magnification with a green light source.
Benzer Ürünler
Bunlar da ilginizi çekebilir
Özel Telecentric Seri · Telecentric Lens
TCSE10M009-J – Opto Engineering Telecentric Lens
Fiyat için teklif alın
Özel Telecentric Seri · Telecentric Lens
TCSE16M024NIR-F – Opto Engineering Telecentric Lens
Fiyat için teklif alın
Özel Telecentric Seri · Telecentric Lens
TCSE16M024-F – Opto Engineering Telecentric Lens
Fiyat için teklif alın
Özel Telecentric Seri · Telecentric Lens
TCSE16M028VISNIR-F – Opto Engineering Telecentric Lens
Fiyat için teklif alınTeklif İste
Ürün: TCCX050-G – Opto Engineering Koaksiyel Telecentric Lens